Dell Inspiron N5010
简介[编辑 | 编辑源代码]
本文是写给使用使用戴尔灵越N5010计算机用户的Arch Linux配置指南
概要[编辑 | 编辑源代码]
To do[编辑 | 编辑源代码]
- eSata test
- HDMI test
- Force acpi/cpufreq to work (somehow :))
- Need someone with wikimedia syntax skills to guide me formating this wiki page, please :).
Hardware[编辑 | 编辑源代码]
Working[编辑 | 编辑源代码]
Ethernet[编辑 | 编辑源代码]
Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Works out of the box.
DVDRW[编辑 | 编辑源代码]
ATAPI: TSSTcorp DVD+/-RW TS-L633J, D200, max UDMA/100
CD-ROM TSSTcorp DVD+-RW TS-L633J D200 PQ: 0 ANSI: 5
Using driver: scsi3-mmc
Supported extensions:
24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Successfully burns both cd mediums and dvd mediums, tested using K3B 2.0.2-1.
触摸板[编辑 | 编辑源代码]
如果使用Gnome桌面环境那么可以直接使用快捷键来控制触摸板的锁定与开启
未安装Gnome桌面环境的用户控制触摸板需要使用synaptic驱动。
需要安装软件包xf86-input-synaptics.
详细信息可以查看Touchpad Synaptics (简体中文)
Todo: Needs tweaking, cause it is too anoying.
Use this script to disable the touch pad when you do not like it:
#!/bin/bash if [ $(synclient -l | grep TouchpadOff | gawk -F '= ' '{ print $2 }') -eq 0 ]; then synclient TouchpadOff=1 else synclient TouchpadOff=0 fi
Wireless[编辑 | 编辑源代码]
Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) In kernel 2.6 it works out of the box, but in kernel 3.0 there is no wlan0, we have to blacklist some modules.
So open "/etc/modprobe.d/modprobe.conf" and append the following line:
blacklist bcma
now, reboot or restart the kernel.
When we issue iwconfig, it should now list wlan0:
lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"*******" Mode:Managed Frequency:2.427 GHz Access Point: XX:XX:XX:XX:XX:XX Bit Rate=72.2 Mb/s Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:968 Missed beacon:0
Bluetooth[编辑 | 编辑源代码]
详情查看Bluetooth (简体中文)
Both pairing, sending files and receiving files works out of the box, tested with blueman.
VGA[编辑 | 编辑源代码]
Tested on an external CRT monitor, works out of the box on KDE 4.7.
Graphic adapter[编辑 | 编辑源代码]
ATI Mobility Radeon HD 5600 working out of the box.
Audio[编辑 | 编辑源代码]
Intel Corporation 5 Series/3400 Series Chipset High Definition Audio
Display[编辑 | 编辑源代码]
Available sizes:
1366x768 60.0*+ 1280x720 59.9 1152x768 59.8 1024x768 59.9 800x600 59.9 848x480 59.7 720x480 59.7 640x480 59.4
Brightness controls work out of the box.
Suspending to disk (Hibernation)[编辑 | 编辑源代码]
works out of the box - tested on KDE 4.7
Suspending to ram (Sleep)[编辑 | 编辑源代码]
works out of the box - tested on KDE 4.7
Sensors[编辑 | 编辑源代码]
使用lm_sensors软件可以监控计算机各设备的温度,详情查看Lm_sensors (简体中文) 目前只能监测到三个设备的温度:
- radeon-pci-0100(显卡)
- acpitz-virtual-0
- acpi termal zone 0 Temperature
They work out of the box. 如果想监测硬盘温度可以使用[[hddtemp
Partially Working[编辑 | 编辑源代码]
Not Working[编辑 | 编辑源代码]
Processor frequency control[编辑 | 编辑源代码]
- says unsupported I think:
:: Setting cpufreq governing rules [BUSY] grep: /sys/devices/system/cpu/cpu* /cpufreq/scaling_available_governors: No such file or directory, cpu 0 wrong, unknown or unhandled CPU? Error setting new values. Common errors: - Do you have proper administration rights? (super-user?) - Is the governor you requested available and modprobed? - Trying to set an invalid policy? - Trying to set a specific frequency, but userspace governor is not available, for example because of hardware which cannot be set to a specific frequency or because the userspace governor is not loaded? 1wrong, unknown or unhandled CPU? Error setting new values. Common errors: - Do you have proper administration rights? (super-user?) - Is the governor you requested available and modprobed? - Trying to set an invalid policy? - Trying to set a specific frequency, but userspace governor is not available, for example because of hardware which cannot be set to a specific frequency or because the userspace governor is not loaded? 2wrong, unknown or unhandled CPU? Error setting new values. Common errors: - Do you have proper administration rights? (super-user?) - Is the governor you requested available and modprobed? - Trying to set an invalid policy? - Trying to set a specific frequency, but userspace governor is not available, for example because of hardware which cannot be set to a specific frequency or because the userspace governor is not loaded? 3wrong, unknown or unhandled CPU? Error setting new values. Common errors: - Do you have proper administration rights? (super-user?) - Is the governor you requested available and modprobed? - Trying to set an invalid policy? - Trying to set a specific frequency, but userspace governor is not available, for example because of hardware which cannot be set to a specific frequency or because the userspace governor is not loaded? [DONE]
Unknown / Untested[编辑 | 编辑源代码]
HDMI Video[编辑 | 编辑源代码]
Redwood HDMI Audio 5600[编辑 | 编辑源代码]
eSata port[编辑 | 编辑源代码]
Installation[编辑 | 编辑源代码]
Normal installation with no issues to report.
Kernel[编辑 | 编辑源代码]
ATI Mobility Raedon 5600[编辑 | 编辑源代码]
To do: Synaptic guide
Troubleshoot[编辑 | 编辑源代码]
- On boot the following error is printed:
boot error message:
intel ips 0000:00:1f.6: failed to get i915 symbols, graphics turbo disabled
Workaround:
Blacklist the intel_ips module, open configuration file "/etc/modprobe.d/modprobe.conf" and add:
blacklist intel_ips